# hd-idle

Reimplementation of _Christian Mueller's_ [hd-idle](http://hd-idle.sf.net) with some extra features.

`hd-idle` is a utility program for spinning-down external disks after a period of idle time. 
Since most external IDE disk enclosures don't support setting the IDE idle timer, 
a program like `hd-idle` is required to spin down idle disks automatically.

**Index**
* [Extra features](#extra-features)
  * [Support ATA commands](#support-ata-commands)
  * [Monitor the skew between monitoring cycles](#monitor-the-skew-between-monitoring-cycles)
  * [Resolve symlinks in runtime](#resolve-symlinks-in-runtime)
  * [Log disk spin up](#log-disk-spin-up)
  * [Use disk partitions to calculate activity](#use-disk-partitions-to-calculate-activity)
* [Install](#Install)
  * [Precompiled binaries](#precompiled-binaries)
  * [Build from source](#build-from-source)
* [Run hd-idle](#run-hd-idle)
* [Configuration](#Configuration)
* [Understand the logs](#understand-the-logs)
  * [Standard log](#standard-log)
  * [Log file](#log-file)
* [Warning on spinning down disks](#warning-on-spinning-down-disks)
* [Troubleshot](#Troubleshot)
  * [SCSI response not ok](#scsi-response-not-ok)

## Extra features

List of extra features compared to the original `hd-idle`:
 
### Support ATA commands

The implementation of `hd-idle` written by _Christian Mueller_ relies on the `SCSI` api to work.
When listing the drives by id, disks starting with `usb` stop using the original implementation, 
but disk starting with `ata` do not.

    $ ls /dev/disk/by-id/
    
    ata-WDC_WD40EZRX-
    ata-WDC_WD50EZRX-
    usb-WD_My_Book_1140_
    
[hdparm](https://en.wikipedia.org/wiki/Hdparm) on the other hand always stops the drives without any problems.
It uses `ATA` api calls to send disks to standby. `hd-idle` comes with `ATA` commands support to replicate `hdparm`'s api calls.

### Monitor the skew between monitoring cycles

Identify if the sleep took longer than expected and reset the spun down flag if it waited too long for the main loop sleep. 
This should capture suspend events as well as excessive machine load.

### Resolve symlinks in runtime

`hd-idle` can resolve disk symlinks also in runtime. Disks added after application's start won't be hidden. 

### Log disk spin up

Show in standard output when disks spin up. 

### Use disk partitions to calculate activity

The disk activity is calculated by watching read/write changes on partition level instead of disk level.
This is required for kernels newer than 5.4 LTS, because disk monitoring tools change read/write values on disk level,
although there's no real activity on the disk itself.

## Install

There are various ways of installing `hd-idle`:

### Precompiled binaries

Precompiled binaries for released versions are available in the 
[*releases*](https://github.com/adelolmo/hd-idle/releases) section.

### Build from source

To build `hd-idle` from the source code yourself you need to have a working
Go environment with [version 1.16 or greater installed](http://golang.org/doc/install).

You can directly use the `go` tool to download and install the `hd-idle` 
binaries into your `GOPATH`:

    $ go get github.com/adelolmo/hd-idle
    $ hd-idle

On Debian you can also clone the repository yourself and build using `dpkg-buildpackage`.

    $ git clone https://github.com/adelolmo/hd-idle.git
    $ cd hd-idle
    $ dpkg-buildpackage -a armhf -us -uc -b
    
In the example above, the package is built for `armhf`, but you can build it also for the platforms `i386`, `amd64`, and `arm64` 
by substituting the parameter `-a`.
    
Then install the package:

    # dpkg -i ../hd-idle*.deb
    
## Run hd-idle

In order to run `hd-idle`, type: 

    $ hd-idle
    
This will start `hd-idle` with the default options, causing all `SCSI` 
(read: USB, Firewire, SCSI, ...) hard disks to spin down after 10 minutes of inactivity.

If the Debian package was installed, after editing `/etc/default/hd-idle` and enabling it (`START_HD_IDLE=true`), 
run hd-idle with:

    # systemctl start hd-idle
    
To enable `hd-idle` on reboot:

    # systemctl enable hd-idle    

Please note that `hd-idle` uses */proc/diskstats* to read disk statistics. If
this file is not present, `hd-idle` won't work.

In case of problems, use the debug option *-d* to get further information.

## Configuration

Command line options:

+ -a *name*              
                        Set device name of disks for subsequent idle-time
                        parameters *-i*. This parameter is optional in the
                        sense that there's a default entry for all disks
                        which are not named otherwise by using this
                        parameter. This can also be a symlink
                        (e.g. /dev/disk/by-uuid/...)
                         
+ -i *idle_time*          
                        Idle time in seconds for the currently named disk(s)
                        (-a *name*) or for all disks.
                        Setting this value to `0` will never spin down the disk(s).
                         
+ -c *command_type*       
                        Api call to stop the device. Possible values are `scsi`
                        (default value) and `ata`.

+ -s *symlink_policy*   
                        Set the policy to resolve symlinks for devices. If set 
                        to `0`, symlinks are resolved only on start. If set to `1`,
                        symlinks are also resolved on runtime until success.
                        By default symlinks are only resolved on start. If the 
                        symlink doesn't resolve to a device, the default
                        configuration will be applied.

+ -l *logfile*            
                        Name of logfile (written only after a disk has spun
                        up or down). Please note that this option might cause the
                        disk which holds the logfile to spin up just because
                        another disk had some activity. On single-disk systems,
                        this option should not cause any additional spinups.
                        On systems with more than one disk, the disk where the log
                        is written will be spun up. On raspberry based systems the 
                        log should be written to the SD card.

Miscellaneous options:

+ -t *disk*               
                        Spin-down the specified disk immediately and exit.
 
+ -d                      
                        Debug mode. It will print debugging info to
                        stdout/stderr (/var/log/syslog if started with systemctl)
                         
+ -h                      
                        Print usage information.

Regarding the parameter *-a*:

The parameter *-a* can be used to set a filter on the disk's device name (omit /dev/) 
for subsequent idle-time settings.

1) 
    A *-i* option before the first *-a* option will set the default idle time.

2) 
    In order to disable spin-down of disks per default, and then re-enable
    spin-down on selected disks, set the default idle time to 0.

    Example:
    ```
    hd-idle -i 0 -a sda -i 300 -a sdb -i 1200
    ```
    This example sets the default idle time to 0 (meaning hd-idle will never
    try to spin down a disk) and the default api command to `scsi`, then sets explicit 
    idle times for disks which have the string `sda` or `sdb` in their device name.
 
3) 
    The option *-c* allows to set the api call that sends the spindown command.
    Possible values are `scsi` (the default value) or `ata`.
    
    Example:
    ```
    hd-idle -i 0 -c ata -a sda -i 300 -a sdb -i 1200 -c scsi
    ```  
    This example sets the default idle time to 0 (meaning hd-idle will never
    try to spin down a disk) and the default api command to `ata`, then sets explicit 
    idle times for disks which have the string `sda` or `sdb` in their device name 
    and sets `sdb` to use `scsi` api command.

## Understand the logs

By default `hd-idle` only logs to the standard output. You can find them in the syslog if the application starts via service.

If you set the log file (`-l` flag) then the application writes extra details to it. (Check the [Configuration](#Configuration) section).

### Standard log

The standard log output registers two kinds of events:

* disk spin up
* disk spin down

```
Aug  8 00:14:55 enterprise hd-idle[9958]: sda spindown
Aug  8 00:14:55 enterprise hd-idle[9958]: sdb spindown
Aug  8 00:14:56 enterprise hd-idle[9958]: sdc spindown
Aug  8 00:17:55 enterprise hd-idle[9958]: sdb spinup
Aug  8 00:28:55 enterprise hd-idle[9958]: sdb spindown
```

### Log file

You can enable the log file with the flag `-l` followed by the log path. (Check the [Configuration](#Configuration) section).

This is the kind of entry shown in the log file:

```
date: 2020-07-29, time: 07:59:57, disk: sdc, running: 601, stopped: 76654
```

Explanation:
* `date` and `time` when the disk spins up.
* `disk` involved.
* `running` seconds the device was running before it spun down the last time.
* `stopped` seconds since last spin down. This is the time the disk was asleep before spinning up.

A bit more on `running` explained with an example:

| timestamp | current disk spin | event | running | stopped |
| :-------------: | :----------: | :-----------: | :-----------: | :-----------: |
| 5:00 | down | disk activity | ? | ? |
| 6:00 | up | go to sleep | - | - |
| 9:00 | down | disk activity | 6:00 - 5:00 = 1h (3600s) | 9:00 - 6:00 = 3h (10800s) |

Explanation:

At 5:00 the disk is on standby and hd-idle detects disk activity.

At 6:00 the disk is active and hd-idle determines inactivity of the disk and spins it down.

At 9:00 the disk is on standby and hd-idle detects disk activity. It writes on the log file 1h of previous disk spin up and 3h of standby.   


## Warning on spinning down disks

A word of caution: hard disks don't like spinning up too often. Laptop disks
are more robust in this respect than desktop disks but if you set your disks
to spin down after a few seconds you may damage the disk over time due to the
stress the spin-up causes on the spindle motor and bearings. It seems that
manufacturers recommend a minimum idle time of 3-5 minutes, the default in
`hd-idle` is 10 minutes.

One more word of caution: `hd-idle` will spin down any disk accessible via the
`SCSI` layer (USB, IEEE1394, ...) but it will NOT work with real `SCSI` disks
because they don't spin up automatically. Thus it's not called scsi-idle and
I don't recommend using it on a real `SCSI` system unless you have a kernel
patch that automatically starts the `SCSI` disks after receiving a sense buffer
indicating the disk has been stopped. Without such a patch, real `SCSI` disks
won't start again and you can as well pull the plug.

You have been warned...

# Troubleshot

This section covers some usual issues that user's face while using `hd-idle`.

## SCSI response not ok

You can find information about the issue here: [SCSI-response-not-ok](https://github.com/adelolmo/hd-idle/wiki/SCSI-response-not-ok)

## License

GNU General Public License v3.0, see [LICENSE](https://github.com/adelolmo/hd-idle/blob/master/LICENSE).
